How To Repair Wd Diagnostic Error Codes (Solved)


Home > Error Code > Wd Diagnostic Error Codes

Wd Diagnostic Error Codes

Contents

Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number. All Rights Reserved. May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. navigate here

Drive should be replaced. Retest. Retest after checking the connections. Re-test Drive 136 Bad Sector Sector Marked Bad Error. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Dell Hard Drive Error Codes

to report if a drive has failed, it must be enabled as a system option. Re-test Drive 148 Not Selected Drive not selected. This may be due to a media error. If the error repeats, replace the drive.

  • Several instances of information on data positioning and location could not be found.
  • I installed the WD Smartware software included with the Drive and did a Quick Format using WD Quick Formatter (also included).
  • Replace Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9.
  • At least ten ECC errors have been detected.
  • In order for S.M.A.R.T.
  • Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition.
  • psongman 2011-11-21 15:01:30 UTC #3 Hi, well, I got it to work and it repaired all the errors, given an error code of 223.
  • Retest.
  • Re-test Drive If an error code is encountered that is not in the list above, please Contact Us for additional troubleshooting.
  • Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. At least ten errors have been detected. This may be an anomaly. Replace Drive 214 10+ DAM Errors Data Address Mark (DAM) 10+.

Check cabling and retest. Wd Error Codes To run in ATA 66 and ATA100 rates, an Ultra ATA 80 -conductor cable must be used. Replace Drive 557 SERVO 2-9 SERVO is data on track location. https://support.wdc.com/KnowledgeBase/answer.aspx?ID=654 Several instances of information on data positioning and location could not be found.

Replace the drive if the error repeats. Drive should be replaced. Retest after checking the connections. Drive should be replaced.

Wd Error Codes

Replace the drive if the error repeats. This error may also appear if the floppy has been infected by a hidden virus. Dell Hard Drive Error Codes So, I rebooted, hoping to get into Windows XP and get my computer up and running again, NOT, it didn't work. Western Digital Error Code 0007 Re-test Drive with appropriate diagnostic utility 204 Missing Log File The log file that existed at startup of diagnostic utility has been moved or no longer exists.

Retest. http://nbxcorp.com/error-code/voltas-ac-error-codes-e5.html Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. The automatic repair feature can attempt a repair if possible. This may be due to a defect with the drive or a bad connection. Seatools

The printer may not be attached or turned on. Track 0 also holds information about the drive. Use the appropriate version. http://nbxcorp.com/error-code/wii-error-codes-101.html Did several high-level formats and still no dice.

SERVO is data on track location. Check cabling & retest. Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted.

The drive should now be defect free.

Retest. There were media errors that were within the repair capabilities of diagnostic utility. Check cabling and retest. Retest the drive with Data Lifeguard.

Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received. Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. Re-Test Drive 100 Errors Found A Read or Write command during the test has failed. http://nbxcorp.com/error-code/wep-error-codes.html Replace the drive.

ECC is a hardware correction technique that corrects errors. Replace Drive 570 No Recalibration Recalibration command failed. At least ten errors have been detected. Check cabling & retest.

Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. Check cabling & retest. Re-test the drive with Data Lifeguard. The printer may not be attached or turned on.

Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. It also may be due to a defective connection. Retest after checking the connections. hlvadgama 2011-08-07 17:06:25 UTC #3 Thank you for the reply.

Replace the drive if the error repeats. Re-Test Drive 16 Random Read Error A read command during the test has failed. Replace Drive 217 2-9 SERVO Errors SERVO 2-9. Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received.

Please ensure that you are using the appropriate version of diagnostic utility. Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. Self-Monitoring, Analysis, and Reporting Technology (SMART). Replace the drive.

Replace the drive if the repair fails.