How To Repair Whirlpool Duet Sport Error Code F-27 Tutorial


Home > Error Code > Whirlpool Duet Sport Error Code F-27

Whirlpool Duet Sport Error Code F-27

Contents

Plug in washer or reconnect power. 6. This is usually caused by the pump not draining completely. Check the drive motor for powered rotations. 6. This error is saying that the motor control board has gotten too hot and may need to be replaced. his comment is here

Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). If you can’t look through it, exchange Steamer. 5. If there does not seem to be suds, check all the connections to the pressure switch and drain pump. Check for loose connectors. 3. http://www.shopyourway.com/questions/1087402

F27 Error Code Kenmore

Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. or it's affiliates. Check the drain hose and make sure it is not plugged or kinked. 2. Very good information by the way.

  • F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs.
  • Check the pressure switch. 8.
  • F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED.
  • If the washer is still having a problem you likely need a new main control board.
  • F09 Overflow condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur.

Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Replace CCU board. Unplug washer or disconnect power. 2.

You've replaced the water level switch, but check and make sure the connector on the new switch, and the harness to the CCU(main control board), did not get knocked loose during Whirlpool 6th Sense Washing Machine Error Codes F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1. Check/clean drain pump filter of foreign objects. 5. http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html Check door switch/lock unit for foreign objects. 2.

NOTE: The door switch/lock unit can be manually unlocked. Skip to content Sign In Join or Activate Products Departments Departments Shop Shop Explore Explore Advice Advice Rewards Rewards More More Home / Brands / Manage My Life / Questions Check door switch/lock unit for foreign objects. 2. I went out and bought a new pressure switch in the tune of $145 and this has not solved the problem.

Whirlpool 6th Sense Washing Machine Error Codes

Check the drain hose and make sure it is not plugged or kinked. 2.

Check the inlet valve for proper shut off.7. F27 Error Code Kenmore Check Steamer for continuity (Abnormal =infi nity). 2. Whirlpool Front Load Washer Error Codes I think the door lock system might be the next part to look at??

Plug in washer or reconnect power. 5. this content If everything looks good on the connection end then how lucky do you feel?! JPlovesLIFE 25,671 views 7:35 Whirlpool duet sport F21 error code fix - Duration: 4:39. I'm pretty sure you'll be fine after these checks,repairs. Whirlpool Washer

Unplug washer or disconnect power. 3. Check wires and connectors from control to latch switch, then from latch switch to control. Check the drain hose and make sure it is not plugged or kinked. 2. weblink Check drain pump. 7.

The relay might be soldered or always open. F1 Board failure Replace control board (also called ERC or clock). If the above does not correct the problem, replace the pump.

Replace User Interface if drum is rotating. 4.

Try to reset the Duet washer's memory by unplugging the washer for 2 minutes. Check mains supply is in range (90V-132V). The F21 long drain error is referring to duration not length. Check the water temperature sensor and connection to it. 3.

The failure will be reset after running the Diagnostic Test Program is run. 1. Check drive motor tachometer resistance. Electronic Board and the valve for steam fill. 4. check over here F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off.

Door not opened during 3 consecutive cycles. 1. Replace User Interface if drum is rotating. 4. Replace CCU board. Check mechanical linkage from dispenser motor to the top of the dispenser. 3.

MAIN RELAYS ERROR One of the main relays is not working properly. For SELF CLEAN models: check door lock operation. 3. codes. experience as a certified appliance technician. 10522817 Type Your Appliance Question Here...

The control should not allow the unit to run in this condition. F2 Oven temperature is too high 1.