Unplug washer or disconnect power. 2. Potential Causes • Door lock is broken. • Check door lock switch for foreign objects • Check wire harness connections to the door lock switch and the main control board at Browse Categories Answer Questions Kenmore Elite 45986 Front Load Washer Kenmore Elite Washing Machine Kenmore Washing Machine Washing Machines All Unanswered Join Sign In Ask a Question × HomeForumWashing MachinesKenmore EliteElite Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2. his comment is here
Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. NOTE: The door switch/lock unit can be manually unlocked. Door switch open while door is locked. 1.
If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. The failure will be reset after running the Diagnostic Test Program. Press PAUSE/CANCEL twice to clear the display. Check for drain pump failure.6.
Sign in Loading... This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Replace CCU board. Whirlpool Washer F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1.
Check the pressure switch. 8. If code re-appears, replace control board (also called ERC or clock). Check the drive motor for powered rotations. http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html Verify CCU operation by running a Diagnostic Test or any cycle.
Verify CCU operation by running a Diagnostic Test or any cycle. there may be something in the pump impeller or the hose going out from it, if you can get me the full model # XXXXX'll send you a link to the The F21 long drain error is referring to duration not length. You will need to check to following: 1.
Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2. http://www.appliancehelponline.com/whirlpool.html To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. Kenmore F27 Error Check the water temperature sensor and connection to it. Whirlpool 6th Sense Washing Machine Error Codes Unplug washer or disconnect power. 3.
Check the drive motor for powered rotations. this content Check drain pump. 7. Unplug washer or disconnect power. 2. Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. Whirlpool Duet Dryer Error Codes
Check the drive motor for powered rotations. 8. F70 Main Control Heartbeat Failure Error The Duet washer's main control board is unable to connect to the washers user interface. (the control buttons) Check all the connections between the User Check the pressure sensor. weblink Check wire harness connections to the User Interface and the Central Control Unit. 3.
Watch Queue Queue __count__/__total__ Whirlpool Duet Sport Washer Error Codes F-22, F-29 and F-01 DudeWhitman SubscribeSubscribedUnsubscribe5959 Loading... If the condition continues four times, the F31 code will show. 1. Check door switch/lock unit for foreign objects. 2.
Check the drain pump filter for foreign objects. Check the inlet valve for proper shut off. 7. Unplug washer or disconnect power. 3. Now for the error F27, that is a water level error.
F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1. is there a way to get it restarted to drain? The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. check over here It will try to unlock the door 6 times before displaying the error.
Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). My advice for that would be a Mossberg 500. F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. Run a NORMAL cycle without adding any detergent.
F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. The time now is 06:37 PM. If failure still present: 3. Perform Service Cycle to pair the UI and CCU SW. 2.
F62 STEAMER ELECTRONIC BOARD RELAYS ERROR One of the steamer relays (K1, K2, K3, K4) on the Steamer Electronic board have failed, there is an open or short circuit. When I go to start the cycle door clicks drum rotates and then water leaks 1 answer Related Questions'>I have whirlpool Duet sport and get a error code F-33, help? 1 Close Yes, keep it Undo Close This video is unavailable. NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed.
Door switch/lock unit failure. 1. Verify there is not a siphon problem. 3. Check for continuity of the User Interface harness. 2. If the washer is still having a problem you likely need a new motor control board.
Check Steamer for continuity (Abnormal =infi nity). 2. Replace the Motor Control Unit.
© Copyright 2017 nbxcorp.com. All rights reserved.