Fix Whirlpool Duet Washer Error Codes F 27 (Solved)


Home > Error Code > Whirlpool Duet Washer Error Codes F 27

Whirlpool Duet Washer Error Codes F 27

Contents

F35 ANALOG PRESSURE SENSOR FAILURE If this failure is displayed, there is any malfunction of the steamer component detected by the Steamer Electronic Board. 1. Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). Check the inlet valve for proper shut off. 7. Check the drain hose and make sure it is not plugged or kinked. 2. his comment is here

Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Tip & How-To about Kenmore Elite 45986 Front Load Washer F27 Error Code on Whirlpool Exchange steamer electronic board. Follow ApplianceAssistant on Twitter! Check the MCU by looking for operations of the drive motor. 7.

Whirlpool Duet F27 Error Code

F34 UNLOAD INDICATION This failure is only for information and can be displayed in the error history during the Diagnostic Test. or MCU/Motor issue? Apr 05, 2010 | Kenmore Elite 45986 Front Load Washer 1 Answer F27 Error Code on Whirlpool Duet & Kenmore Elite Front Loader Washers Mar 07, 2010 | Washing Machines 2 By reading any content on this site you agree to AppliancePartsPros.com , Inc.

If none of this works, you may have to repalce the water level switch. SamuraiRepairman 63.254 visualizaciones 6:16 Kenmore Elite HE3t/Whirlpool Duet Washer F11 Repair - Duración: 34:06. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). Whirlpool Washer Check the electrical connections at the pump and make sure the pump is running. 4.

Check Pressure Switch harness for continuity. 2. Perform Service Cycle to pair the UI and CCU SW. 2. Open the lid or press STOP/CANCEL to clear the display. Oops!

In this case, replace control board (also called ERC or clock). Replace the Motor Control Unit. Exchange steamer electronic board if valve is OK. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4.

F27 Error Code Kenmore

F06 STEAMER DEFECT The Steamer temperature has not reached the correct value. http://applianceassistant.com/Washer-Repair/Duet-Washer-2nd-Gen/Duet-Washer-Error-Codes.php Check Steamer for continuity (Abnormal =infi nity). 2. Whirlpool Duet F27 Error Code F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. Whirlpool Front Load Washer Error Codes NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1.

Replace User Interface. this content Check/clean drain pump filter of foreign objects. 5. Check the MCU by looking for operations of the drive motor. 7. I can't open door to get model number. Whirlpool 6th Sense Washing Machine Error Codes

  1. how-2-repair.com 4.509 visualizaciones 16:14 Whirlpool Duet Sport Washer, will not drain - Duración: 10:00.
  2. Your Duet washer has a bad door switch. 2.
  3. Vuelve a intentarlo más tarde.
  4. Washer will sometimes complete a full cycle but rarely....what now?
  5. Replace failed component.
  6. If resistance is 0 Ω or infi nite value, replace NTC. 4.
  7. all the lights that should be on, are on… nothing happens.
  8. We had 5 baby socks clogging up the washer from draining.

Check the drive motor for powered rotations. 6. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. weblink When I go to start the cycle door clicks drum rotates and then water leaks 1 answer Related Questions'>I have whirlpool Duet sport and get a error code F-33, help? 1

Login|Contact Us Appliance Need Appliance Repair Help? In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). 4.

Check resistance of heating element, if present on this model. (abnormal = infinity) 4.

F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down. did you remove the pump to see if theres something in it? Unplug washer or disconnect power. 3. The machine will drain for 3 minutes before unlocking the door. 3.

where is the coin catch? Check the drive motor for powered rotations. 8. Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! http://nbxcorp.com/error-code/whirlpool-duet-washer-error-codes-f-11.html If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way.

Check the drain hose and make sure it is not plugged or kinked. 2. Check the inlet valve for proper shut off. 7. Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, The wires should be to the left when facing the MCU connectors. 9.

Acción en curso... Plug in washer or reconnect power. 4. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU The failure will be reset after running the Diagnostic Test Program. 1.

Short circuit of Heater to Ground. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 2. F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1.

Check for continuity of the User Interface harness. 2.