How To Repair Whirlpool F1 Error Oven Tutorial


Home > Error Code > Whirlpool F1 Error Oven

Whirlpool F1 Error Oven

Contents

Also check for any causes of high resistance in the oven temperature sensor circuit. Loading... Check the drive belt and reconnect power and plug unit in. Electrical parts are almost always non-returnable at the parts store. his comment is here

If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. This board is also sometimes referred to as a circuit board, control board, mother board, or an ERC, which is an abbreviation for Electronic Range Control. Sensor resistance should be 1K to 1.1K @ room temperature. F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect.

Whirlpool Range Error Code F9e0

If there is NO water in the unit, make sure the valves are turned on all the way. Check door switch circuit for open.F5 E1Door latch not operatingCheck that door switch is completely closed. Top 4 Reasons Gas Oven Won’t Turn On?

Irvington, NY "I LOVE seeing customer service excellence, seeing follow through on promises." Gregory R. If problems occur with the microwave, many microwave ovens will display an error code, such as "F2." ... Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). Whirlpool Microwave Error Codes F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect.

If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Whirlpool Washing Machine Error Codes E1 If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. Sensor resistance should be 1K to 1.1K @ room temperature. Yes No Thanks!

Re-apply power and observe for at least one minute. 3. Whirlpool Top Load Washing Machine Error Codes Also check for any causes of high resistance in the oven temperature sensor circuit. The installation of the... Select 'cancel' and observe for one minute for errors.

  • Press 'Stop/Cancel' to clear display.
  • Also check all components for defects.
  • User must unlatch and delete the "---" to try to relatch the door.
  • Skip navigation Sign in Loading...
  • LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display.
  • F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.

Whirlpool Washing Machine Error Codes E1

Published on Oct 31, 2014Visit us at http://www.appliancevideo.comDo-it-yourself diagnostic and repair videos brought to you by ApplianceVideo.comApplianceVideo.com takes you into a customer’s actual home with Ace Appliance and teach you how

Sign in to make your opinion count. Whirlpool Range Error Code F9e0 They don't build ovens. Whirlpool Top Load Washer Error Codes Press STOP/CANCEL to clear the display.

Appliance Princess 3,184 views 2:58 Checking an Oven Temperature Sensor - Duration: 3:58. this content If present, replace control board (clock). You may have to register before you can post: click the register link above to proceed. F1 - Control Board Failure - Replace control board (clock). Whirlpool Oven Error Codes E2 F3

Close the lid and press START to continue with the cycle. F2 will appear. F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. weblink For instance, at 350 degrees, the resistance should be 1654 ohms plus or minus 10.8 ohms.

F15 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Whirlpool Oven Temperature Sensor Whirlpool ranges generally use the same error codes, for easy reference, though you may also wish to consult with your range's specific manual for greatest certainty. Gas Burner Sparks All The Time?

Check for drain pump failure and clean it of any debris.

Press 'Stop/Cancel' to clear display. Overloading the unit may cause this problem. The door should now be unlocked. Whirlpool Accubake Oven Error Codes Check for stuck lock switch.

I appreciate the advice. LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. Unplug unit and disconnect power. check over here Ask a question Get up to 50 % off On Wall Ovens Related Questions Related Questions'>What does "E1-F1" error code mean on a Whirlpool wall oven/microwave? 1 answer Related Questions'>What does

It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds. Reply With Quote Page 1 of 2 12 Last Jump to page: Quick Navigation Whirlpool/Roper Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Announcements Membership If you see F3 - E0, the oven temperature sensor has opened and needs to be replaced. This may signify problems with the drive motor, thermal protector or motor controller.

Press 'Stop/Cancel' to clear display. This should change to the F02 error code after a few minutes. I will look again while I have the back off. For SELF CLEAN models, check door lock operation.

Got through thanksgiving and then yesterday we had a power failure and when the power came back on the range said PF (power failure). If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. LF Long fill If the water fill time exceeds ten minutes, the water valves are turned off and "LF" is flashed. See Details Whirlpool WOD51EC0AW 30" Electric Double Wall ...

The oven will come on and heat up to about 150 to 170 and turn off.