How To Fix Whirlpool Duet Error Codes F 27 Tutorial


Home > Error Codes > Whirlpool Duet Error Codes F 27

Whirlpool Duet Error Codes F 27

Contents

Verify CCU operation by running a Diagnostic Test or any cycle. Open and close the door. 2. Household power supply is too low. 2. Loading... his comment is here

I think the door lock system might be the next part to look at?? Unplug washer or disconnect power. 8. Some things to consider: a. Check the pressure switch for proper operation. http://www.fixya.com/support/r1484133-f27_error_code_whirlpool_duet_kenmore

Kenmore F27 Error

Verify the shipping system including shipping bolts, spacers and cables are removed. 2. is the pump turning? Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Press STOP/CANCEL to clear the display.

Possible Causes/Procedure Door lock mechanism is broken or removed from door. Exchange Steamer if it is totally blocked. Check the electrical connections at the pump and make sure the pump is running. 4. Check mechanical linkage from dispenser motor to the top of the dispenser.

We had 5 baby socks clogging up the washer from draining. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check for Drain Pump Failure Check the Inlet Valve Turn off hot and cold water faucets and unplug the unit before servicing. 1.

The relay might be soldered or always open. Check/clean drain pump filter of foreign objects. 5. Front Load ... CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once.

Whirlpool 6th Sense Washing Machine Error Codes

Installed that yesterday and a new set of errors came up. http://applianceassistant.com/Washer-Repair/Duet-Washer-2nd-Gen/Duet-Washer-Error-Codes.php Replace User Interface if drum is rotating. 4. Kenmore F27 Error If too much detergent was used: – Run the unit through a RINSE/SPIN cycle. – Run a NORMAL cycle without adding any detergent. Whirlpool Front Load Washer Error Codes F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral.

Unplug washer or disconnect power. 2. this content Verify CCU operation by running a Diagnostic Test or any cycle. Mismatch of User Interface and CCU or corrupted EEPROM. 1. Check the water temperature sensor and connection to it. 3.

The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω. Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). Check/clean drain pump filter of foreign objects. 5. weblink F28 Serial Communication Error This error means that the main control and the motor control are not able to communicate.

MAIN RELAYS ERROR One of the main relays is not working properly. It is running poorly 11/1/2016 11/1/2016 centralappliance1 I have a GE microwave, - 2004- model JVM1870WF02. Check wire harness connections to the User Interface and the Central Control Unit. 3.

Unplug washer or disconnect power. 8.

  1. Ft.
  2. If failure still present: 3.
  3. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 5. NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed. APP TEAM Find Appliance Parts at AppliancePartsPros.com - Largest inventory in the U.S. Check the drain hose and make sure it is not plugged or kinked. 2.

Replace the pump. F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. The failure will be reset after running the Diagnostic Test Program. 1. check over here Check the water temperature sensor and connection to it.

Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. Door switch open while door is locked. 1. Try to reset the Duet washer's memory by unplugging the washer for 2 minutes.