How To Fix Winsock Api Error 11004 Tutorial


Home > Socket Error > Winsock Api Error 11004

Winsock Api Error 11004

Contents

I'm sorry, I'm completely tired of you and this question. Berkeley description: A connect request was made on an already connected socket; or, a sendto() or sendmsg() request on a connected socket specified a destination when already connected. However, the WSAEPROTONOSUPPORT is another possible equivalent for WinSock to use in place of this error. This is not a soft error, another type of name server request may be successful. have a peek at this web-site

This error occurs if an application passes an invalid pointer value, or if the length of the buffer is too small. A blocking operation was interrupted by a call to WSACancelBlockingCall(). The application may be accessing a socket which the current active task does not own (i.e. Specifically, v1.1 WinSock spec notes that this error occurs if the length of the buffer is too small.

Socket Error 10054

it cannot retrieve a directory listing or files.In certain firewall configurations, users may encounter Connection Refused errors (#10061) when using SyncBackSE/Pro to establish a connection to a remote site. Socket Error # 10052: The host you were connected to crashed and rebooted. The error can also occur in an attempt to rename a file or directory or to remove an existing directory.WSAEFAULT (10014) Bad addressThe system detected an invalid address in attempting to WSAENETRESET (10052) Net dropped connection or reset The host you were connected to crashed and rebooted.

  • You should simply ignore this error when it occurs.WSAEINTR (10004) Interrupted system call A blocking operation was interrupted by a call to WSACancelBlockingCall.
  • Developer suggestions: Every application that uses non-blocking sockets must be prepared for this error on any call to the functions mentioned below.
  • the FTP server is no longer connected to the network.
  • WSAETIMEDOUT 10060 Connection timed out.
  • If not, check with your Winsock vendor to see if they have a newer Winsock available.
  • Note the British spelling (with an 'S' instead of a 'Z').
  • The error can also occur in an attempt to rename a file or directory or to remove an existing directory.

WSAEWOULDBLOCK (10035) Resource temporarily unavailable. WinSock functions: accept(), listen(), recv(), recvfrom(), send(), sendto() WSAEPFNOSUPPORT (10046) Protocol family not supported. WSAEMSGSIZE 10040 Message too long. Socket Error 10054 Connection Reset By Peer Returned by WSARecv and WSARecvFrom to indicate that the remote party has initiated a graceful shutdown sequence.

An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. WSA_QOS_POLICY_FAILURE 11011 QoS policy failure. This is not the solution for this problem.People here have not encountered any DNS SERVER PROBLEM to use their internet applications.This answer can not be considered as an experts answer. 0 http://www.sockets.com/err_lst1.htm If the hostname resolution uses a local hosttable, it's possible you resolved to an old obsolete address.

However, some WinSocks fail with WSAEINVAL you call connect() a second time (or subsequent) on a non-blocking socket. Socket Error 11004 This is because the firewall is blocking the connection as the permissions for the SyncBackSE/Pro application (within the firewall) are being set to "Trusted Application" instead of "SYSTEM", which will give WSAENOTSOCK (10038) Socket operation on non-socket. Either the application hasn't called WSAStartup(), or WSAStartup() failed.

Socket Error 10053

User suggestions: Check that the WINSOCK.DLL file is in the current path Check that the WINSOCK.DLL file is from the same vendor as your underlying protocol stack. http://www.hardhats.org/cs/broker/docs/winsock.html after failed calls to inet_addr() or gethostbyname()), then simply test your address value for zero before you pass it to sendto(). Socket Error 10054 WSATRY_AGAIN 11002 Nonauthoritative host not found. Socket Error Codes Linux Read my lips, IT DOESN'T KNOW!

This is one of the most frequent errors and one of the best to encounter, since it's one of the least ambiguous. http://nbxcorp.com/socket-error/winsock-error-11004-wsano-data.html This normally results from an attempt to bind to an address that is not valid for the local computer. A Host Name or IP address cannot be entered followed by a colon and the port number. WinSock description: a quick comparison to the Berkeley counterpart, and a long description of WinSock error. Socket Error 10049

We have two machines A and B which does not have static ip(which means that we have not registered any domain name) and therefore our ISP will offer dynamic ip( this On a datastream socket, the connection was reset. WSAEMSGSIZE (10040) Message too long A message sent on a socket was larger than the internal message buffer or some other network limit. Source If required, please consult your firewall administrator or vendor for advice.

Note that this error is returned by the operating system, so the error number may change in future releases of Windows. Winsock Error 10061 Basically, you want to identify where the problem occurred. Berkeley description: A message sent on a socket was larger than the internal message buffer or some other network limit.

If it does respond, then this problem might have been a transient one (so you can reconnect now), or the server application you were connected to might have terminated (so you

WSASYSNOTREADY 10091 Network subsystem is unavailable. Video by: Pooja vivek This video is in connection to the article "The case of a missing mobile phone (https://www.experts-exchange.com/articles/28474/The-Case-of-a-Missing-Mobile-Phone.html)". PLEASE DO NOT ACCEPT THIS COMMENT AS AN ANSWER! ====== Werner 0 LVL 6 Overall: Level 6 Message Expert Comment by:Mindphaser2002-08-21 Force accepted ** Mindphaser - Community Support Moderator ** Winsock Error Windows 7 It's also possible that the local services file has an incorrect port number (although it's unlikely).

WSAESTALE 10070 Stale file handle reference. This error is returned if any Windows Sockets API function is called while a blocking function is in progress. Downloads and tools Windows 10 dev tools Visual Studio Windows SDK Windows Store badges Essentials API reference (Windows apps) API reference (desktop apps) Code samples How-to guides (Windows apps) Learning resources have a peek here There are no QoS receivers.