How To Fix Winsock Bind Error 10038 Tutorial


Home > Socket Error > Winsock Bind Error 10038

Winsock Bind Error 10038

Contents

WinSock functions: accept(), listen(), recv(), recvfrom(), send(), sendto() WSAEPFNOSUPPORT (10046) Protocol family not supported. A system call that should never fail has failed. asked 4 years ago viewed 2155 times active 4 years ago Blog Stack Overflow Podcast #93 - A Very Spolsky Halloween Special Related 0send(), returns Winsock Error 100381Bind Error 10038 with The time now is 06:33 PM. http://nbxcorp.com/socket-error/winsock-error-10038.html

Berkeley description: The host you were connected to crashed and rebooted. By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving, or both have been discontinued. WSATRY_AGAIN 11002 Nonauthoritative host not found. Alternately, you can get the local IP address by calling gethostname() followed by gethostbyname(). check it out

Socket Error 10038

Berkeley description: The protocol family has not been configured into the system or no implementation for it exists. This would occur if WinSock aborts an established connection after data retransmission fails (receiver never acknowledges data sent on a datastream socket). This is one of the most frequent errors and one of the best to encounter, since it's one of the least ambiguous. This won't reveal too much unless you know the router addresses at the remote end, but it might help to identify if the problem is somewhere along the way.

WinSock description: Same as Berkeley. Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE but the connection has already been aborted (e.g. WinSock functions: accept(), bind(), connect(), gethostname(), getpeername(), getsockname(), getsockopt(), recvfrom(), send(), sendto(), setsockopt() if buffer length is too small. Socket Error 10054 Connection Reset By Peer Change the following line to; SOCKET Socket=socket(AF_INET,SOCK_STREAM,IPPROTO_UDP); What we have done here is mix and match TCP/IP elements (SOCK_STREAM) and UDP elements (IPPROTO_UDP), which is a big no no.

WSANO_RECOVERY 11003 This is a nonrecoverable error. Winsock Error 10053 User suggestions: see WSAECONNABORTED for details. For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM. At least one QoS send path has arrived.

Specifically, v1.1 WinSock spec notes that this error occurs if the length of the buffer is too small. Socket Error Codes Linux Generically, the error means the network system has run out of socket handles. WSAEPROTONOSUPPORT 10043 Protocol not supported. If so, is there an older DLL in a directory in the path ahead of the directory containing the newer DLL?

Winsock Error 10053

WSAVERNOTSUPPORTED 10092 Winsock.dll version out of range. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx WSAECONNABORTED 10053 Software caused connection abort. Socket Error 10038 The system detected an invalid pointer address in attempting to use a pointer argument of a call. What Is A Socket Error Developer suggestions: to make your application more portable: with datagram sockets don't use connect() and sendto() on the same datagram socket in an application, and always "disconnect" before calling connect() more

Reply With Quote March 30th, 2011,12:54 AM #6 Alphadan View Profile View Forum Posts Member Join Date Feb 2009 Posts 252 Re: socket function returning = 10038 Originally Posted by MikeAThon http://nbxcorp.com/socket-error/winsock-error-10038-msdn.html WSAECANCELLED 10103 Call has been canceled. WSAENETRESET 10052 Network dropped connection on reset. Berkeley description: A connect request was made on an already connected socket; or, a sendto() or sendmsg() request on a connected socket specified a destination when already connected. Socket Error 10049

  • We took the text of the errno manual page in BSD 4.3, filled in gaps and embellished, completing the information.
  • Why do dealers in Vegas check ID even if I look older than 25?
  • WSAEWOULDBLOCK 10035 Resource temporarily unavailable.
  • An operation was attempted on something that is not a socket.
  • User suggestions: Try to ping the destination host, to see if you get the same results (chances are, you will).
  • When a particular Windows Sockets function indicates an error has occurred, this function should be called immediately to retrieve the extended error code for the failing function call.
  • Note that this error is returned by the operating system, so the error number may change in future releases of Windows.

no funny bisuness. TCP/IP scenario: In BSD-compatible implementations, the local network system generates this error if there isn't a default route configured. WSAEINVAL 10022 Invalid argument. http://nbxcorp.com/socket-error/winsock-10038-error.html WinSock functions: accept(), close socket(), connect(), recv(), recvfrom(), send(), sendto(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() WSAHOST_NOT_FOUND (11001) Host not found Berkeley description: No such host is known.

Mike Last edited by MikeAThon; March 28th, 2011 at 02:36 PM. Socket Error 10061 Connection Refused Other information varies between different errors. In your original post, you said that you received 10038 when calling the socket() function.

wheew) Im new to network programming, but have been working with C++ for the last three years on a hobby level, and also been playing with AS3 recently.

An invalid policy object was found in the QoS provider-specific buffer. Try a "traceroute" to the host you were connected to. Too many links were encountered in translating a pathname. Winsock Error 10061 Back to top #7 Azjherben Members -Reputation: 100 Like 0Likes Like Posted 11 August 2009 - 10:22 AM Quote:Original post by hplus0603The problem is that you increment the client count

WSA_QOS_POLICY_FAILURE 11011 QoS policy failure. In Berkeley, this error also occurs when you are trying to name the local socket (assign local address and port number) with bind(), but Windows Sockets doesn't ascribe this error to This usually means the local software knows no route to reach the remote host. have a peek here Detailed description: There's at least one WinSock implementation that will occasionally fail a function and report this as the error value, even though the function succeeded.

An operation was attempted on a nonblocking socket with an operation already in progress—that is, calling connect a second time on a nonblocking socket that is already connecting, or canceling an Why would you even want to write something like that, what's wrong with SOCKET servSock = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP); if(servSock == INVALID_SOCKET) DieWithError("socket() failed"); ?