How To Repair Winsock Error 0 No Error Tutorial

Home > Socket Error > Winsock Error 0 No Error

Winsock Error 0 No Error


Note that the v1.1 Winsock specification does not explicitly state that this error occurs if the value you request is larger than the WSAData.iMaxUdpDg returned from WSAStartup. WSANO_DATA (11004)* Valid name, no data record of requested type The requested name is valid, but does not have an Internet IP address at the name server. At the DOS prompt, type the following: ping This will ping your local PC. WinSock description: Similar to Berkeley & Microsoft C, the generic meaning is that an application passed invalid input parameter in a function call.

All rights reserved. Any other type of operation might also return this error—for example, setsockopt setting SO_KEEPALIVE if the connection has been reset. Using ping, you can determine quite a bit about your network, including whether the PC is working properly, whether you have a proper DNS and gateway, whether a particular host is If so, treat this as a non-fatal error and ignore it, if possible. check my blog

Socket Error 10038

Copyright © 2016 by Rasmussen Software, Inc. Running the application with this change will give you error 10043 (WSAEPROTONOSUPPORT) which means 'protocol not supported'. However, there are some TCP/IP dialers that install their own Winsock.dll which may not be compatible with our programs. WSAEADDRINUSE 10048 Address already in use.

  • This normally results from an attempt to bind to an address that is not valid for the local computer.
  • What commercial flight route requires the most stops/layovers from A to B?
  • Privacy Policy Legal Steam Subscriber Agreement Portal Search Member List Calendar Help Hello There, Guest!
  • Check all your network configuration settings, and check with the system administrator on the other end.
  • ping This will ping the host you are trying to reach by name.

Detailed descriptions (relevant to socket states): accept(): listen() was not invoked prior to accept() bind(): socket already bound to an address getsockname(): socket not bound with bind() listen(): socket not bound WinSock description: Same as Berkeley. Linear ModeThreaded Mode It appears that you have Javascript disabled or your browser does not support Javascript. Wsagetlasterror 0 closesocket(): occurs on a non-blocking socket with non-zero timeout set with setsockopt() SO_LINGER.

For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM. Winsock Error Windows 7 The ICMP message means that a router cannot forward the IP datagram, possibly because it did not get a response to an ARP request (which might mean the destination host is No more file handles are available, so no more files can be opened.. visit Netstat shows current statistics for your TCP/IP connection.

Berkeley description: A connect or send request failed because the connected party did not properly respond after a period of time. (The timeout period is dependent on the communication protocol.) WinSock Socket Error 10053 Request refused: Name server refuses to satisfy your query for policy reasons. WSA_QOS_EPOLICYOBJ 11025 Invalid QoS policy object. Winsock error codes 10004WSAEINTRInterrupted function call 10009WSAEBADFWSAEBADF 10013WSAEACCESWSAEACCES 10014WSAEFAULTBad address 10022WSAEINVALInvalid argument 10024WSAEMFILEToo many open files 10035WSAEWOULDBLOCKOperation would block 10036WSAEINPROGRESSOperation now in progress 10037WSAEALREADYOperation already in progress 10038WSAENOTSOCKSocket operation on non-socket

Winsock Error Windows 7

WSAEDQUOT 10069 Disk quota exceeded. WSAENOTCONN 10057 Socket is not connected. Socket Error 10038 Thanks a lot! Socket Error Codes Linux WinSock functions: WSAETIMEDOUT (10060) Connection timed out.

Developer suggestion: are you trying to use an optional feature? Check This Out Do not set non-zero timeout on non-blocking sockets to avoid this ambiguity (see Chapter 9 for more information). You should simply ignore this error when it occurs.WSAEINTR (10004) Interrupted system call A blocking operation was interrupted by a call to WSACancelBlockingCall. This error is returned by the WSCGetProviderInfo and WSCGetProviderInfo32 functions if the protocol entry specified could not be found. Socket Error 10054 Connection Reset By Peer

Try setting the key's value to something like 10. For instance, if the length of an argument which is a struct sockaddr is smaller than sizeof(struct sockaddr).WSAEHOSTDOWN (10064)Host is down.A socket operation failed because the destination host was down. WSANOTINITIALISED 10093 Successful WSAStartup not yet performed. The file handle supplied is not valid.

As an example, Bell South noted that if the MTU of the router connecting to their site has an MTU value of more than 1490 there could be problems and long Socket Error 10049 A retry at some time later may be successful. From this you can determine a "down" device or a problem with a gateway address.

US: 1.866.601.2586 | International: +1.817.601.3222 | email Login Register Basket Products MDaemon Private Email Server MDaemon Hosted (Cloud) Email SecurityPlus AntiVirus for MDaemon Outlook Connector for MDaemon SecurityGateway for

See also: WSAECONNABORTED, WSAENETRESET, WSAETIMEDOUT WSAEDESTADDRREQ (10039) Destination address required. The above procedure should only be followed if you are familiar with the Network Control Panel item and its behavior. WSA_IO_PENDING 997 Overlapped operations will complete later. Socket Error 11004 Either the socket handle parameter did not reference a valid socket, or for select, a member of an fd_set was not valid.

WSAHOST_NOT_FOUND for details. If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. WSANO_RECOVERY 11003 This is a nonrecoverable error. Ping a host on the same subnet as the host you were connected to (if you know one).

For example, if a call to WaitForMultipleEvents fails or one of the registry functions fails trying to manipulate the protocol/namespace catalogs. When Anzio comes up, it then also does the Dialer, even if you are trying to connect locally. before calling connect() or accept()). WSAEADDRNOTAVAIL (10049) Can't assign requested address Normally results from an attempt to create a socket with an address not on this machine.

Networking activity on the local host has not been initiated. These conditions are more likely to be indicated by the error WSAETIMEDOUT. Connection closed by peer, winsock error 0 "no error" Cezska View Public Profile Search User Find More Posts by Cezska Find Threads by Cezska Steam Users' Forums > Dedicated All sockets are created with an associated "address family" (i.e.