WSAEBADF (10009) Bad file descriptor. This usually results from trying to connect to a service that is inactive on the foreign host—that is, one with no server application running. The program may be accessing a socket which the current active task does not own (i.e. WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a have a peek at this web-site
By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving, or both have been discontinued. WSAEALREADY 10037 Operation already in progress. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. WinSock description: Same as Berkeley. dig this
Berkeley description: This is a temporary condition and later calls to the same routine may complete normally (also known as EAGAIN error in Berkeley Software Distribution version 4.3) WinSock description: Same WinSock description: No equivalent. What can cause Winsock Error Code 10050 Repair error?
This error is also possible on a datagram socket; for instance, this error could result if your application sends a UDP datagram to a host, which rejects it by responding with Microsoft C description: Bad file number. An operation was attempted on something that is not a socket. Socket Error 11004 WSA_QOS_EPSFILTERSPEC 11028 Invalid QoS provider-specific filterspec.
The error can also occur in an attempt to rename a file or directory or to remove an existing directory. Socket Error Codes Linux A system call that should never fail has failed. This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses WSAESTALE 10070 Stale NFS file handle WSAEREMOTE 10071 Too many levels of remote in path.
A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call. Winsock Error 10061 It could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. WSASYSNOTREADY 10091 Network subsystem is unavailable. Alternately, you could call setsockopt(SO_REUSEADDR) to allow duplicate local addresses in a single application, but this is a kludgy approach (i.e.
Generically, the error means the network system has run out of socket handles. http://www.elbiah.de/hamster/doc/ref/errwinsock.htm The service cannot be found in the specified name space. Socket Error 10054 No connection could be made because the target computer actively refused it. Socket Error 10053 Note that this error occurs rarely since a WinSock implementation cannot reliably detect hardware problems.
BSD-compatible HOSTS, SERVICES or PROTOCOLS files) could not be found, or a DNS request was returned by the server with a severe error.WSAPROVIDERFAILEDINIT (OS dependent)Unable to initialize a service provider.Either a http://nbxcorp.com/socket-error/winsock-error-code-183.html WinSock description: Same as Berkeley. The connection has been broken due to keep-alive activity detecting a failure while the operation was in progress. This unique Winsock Error Code 10050 Repair error code features a numeric value and a practical description. Socket Error 10054 Connection Reset By Peer
WSAEINTR (10004) Interrupted function call. Winsock Error Code 10050 Repair error codes are often brought on in one way or another by faulty files_new in the Microsoft Windows OS. The server application might need to call htons() to translate the port to network byte order in the sockaddr structure. Source Page Options Print this article Email this article Rate this article ©2003-2016 SolarWinds.
This error occurs if an program attempts to bind a socket to an IP address/port that has already been used for an existing socket, or a socket that wasn't closed properly, Winsock Error 10054 Fix WSAESOCKTNOSUPPORT 10044 Socket type not supported. Too many open sockets.
An invalid QoS flow descriptor was found in the flow descriptor list. A problem was encountered with some part of the filterspec or the provider-specific buffer in general. A connection attempt failed because the connected party did not properly respond after a period of time, or the established connection failed because the connected host has failed to respond. Socket Error 10061 Connection Refused Developers should consider handling the referenced errors similarly.
The Fix complete. *File size: 8.5MB Download time: <120 Secs When you have Winsock Error Code 10050 Repair error then we strongly recommend that you run an error message scan. WSAEISCONN 10056 Socket is already connected. Developer suggestion: are you trying to use an optional feature? http://nbxcorp.com/socket-error/winsock-bind-error-10050.html The explanation is simple and obvious: in order to connect to or send to a destination address, you need to provide the destination address.
WSAHOST_NOT_FOUND 11001 Host not found. Berkeley description: No equivalent in 4.3 BSD or compatible operating systems. Developer suggestions: Chances are, that if you encounter this error, your application ignored the failure of some previous function. You could also try to resolve another hostname you know should work, to check that the name resolution server application is running.
WinSock functions: send(), sendto(), setsockopt() Additional functions: Any function that does network I/O: recv(), recvfrom(), FD_READ, FD_WRITE See also: WSAECONNABORTED, WSAECONNRESET, WSAETIMEDOUT WSAENETUNREACH (10051) Network is unreachable. You could use this to verify that you're receiving TCP resets or ICMP Port Unreachable packets each time you attempt to connect. This error apparently also takes the place of WSAEPFNOSUPPORT (which means "protocol family not supported"), since that error is not listed for socket() in the v1.1 WinSock specification. The errors that have User suggestions are all the same ones in the "User-fixable errors" list above.
This is not a temporary error. Berkeley description: A socket operation failed because the destination host was down. This message indicates that the key (name, address, and so on) was not found. There are 2 methods in which to resolve Winsock Error Code 10050 Repair error code: Advanced Solution (advanced): 1) Start your computer and then log on as an administrator. 2) Click
WSANOTINITIALISED 10093 Winsock not yet initialized. WSA_QOS_EFLOWDESC 11026 Invalid QoS flow descriptor. try to ping the server(s)).
© Copyright 2017 nbxcorp.com. All rights reserved.