If you have more than one server configured, the hostname query fails only after the WinSock DLL has queried all servers. So it's still hammering away at other people's connections and this seems to interfier with your irc expirence There's a nice little utility that'll find it and remove it if do If you used a hostname, did it resolve to the correct address? WSAEHOSTDOWN 10064 Host is down. have a peek at this web-site
However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid. If the response is using HTTP 0.9, you must close the socket and reconnect before sending the next HTTP request. If you don't have the proper subnet mask, your network system may treat a local address as a remote address (so it forwards addresses on the local subnet to the router, User suggestions: see WSAHOST_NOT_FOUND for details. page
WinSock description: Same as Berkeley, and then some. without being shut down. you tried to connect to the wrong destination host address the server application isn't running on the destination host the server application isn't listening on the right port.
WinSock description: No equivalent. Does the Raspberry Pi 3 regulate the voltage on its 5V pins? In fact, on occasion you can benefit if the WinSock implementation returns these other errors. Socket Error 11004 Produce Dürer's magic square When I added a resistor to a set of christmas lights where I cut off bulbs, it gets hot.
If it doesn't respond, it might be off-line or there may be a network problem along the way. Winsock Error 10053 So, for example, you can expect this error if a WinSock implementation doesn't support socket type SOCK_RAW within the Internet address family (AF_INET). You could use this to verify that you're receiving TCP resets or ICMP Port Unreachable packets each time you attempt to connect. http://stackoverflow.com/questions/17623563/c-winsock-error-10053 They signal unusual error conditions for which there's no WinSock error equivalent.
some early releases of version 2 of vPOP3 use the recycle bin quite extensively. https://www.experts-exchange.com/questions/10135065/TCP-IP-Error-10053-Sending-Data-using-Sockets.html WinSock description: Almost same as Berkeley. Socket Error 10054 This normally results from an attempt to bind to an address that is not valid for the local computer. Socket Error Codes Linux Return code/valueDescription WSA_INVALID_HANDLE 6 Specified event object handle is invalid.
Operations that were in progress fail with WSAENETRESET. Check This Out A problem was encountered with some part of the filterspec or the provider-specific buffer in general. Request refused: name server refuses to satisfy your query for policy reasons. WinSock functions:
Also, manually configuring your DNS/Gateway/Subnet/etc. thx. –GilAlexander Jul 12 '13 at 22:34 Sorry ya, did that quickly. An application attempted an input/output network function call before establishing an association with a remote socket (i.e. Source Berkeley description: An asynchronous signal (such as SIGINTor SIGQUIT) was caught by the process during the execution of an interruptible function.
You need to call htons() to translate a constant value to network byte order before assigning it to the sin_port field in the sockaddr structure. Asynchronous Socket Error 10053 What is an instant of time? WSA_QOS_ESDMODEOBJ 11029 Invalid QoS shape discard mode object.
NOTE: The MAKEWORD macro referenced in the code fragment is not available in the WINSOCK.H header file or in any standard header files. WinSock description: Unlike Berkeley Sockets, in WinSock WSAEALREADY means that the asynchronous operation you attempted to cancel has already been canceled. It's a bit like getting robbed and then finding out that the culprit lives in Los Angeles; a start, but not particularly helpful.At its core though, a 10053 is typically just Socket Error 10061 Connection Refused User suggestions: There are a number of things to check, that might help to identify why the failure occurred.
WSAEUSERS 10068 User quota exceeded. The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections. A socket operation failed because the destination host is down. have a peek here WinSock functions: accept(), listen(), recv(), recvfrom(), send(), sendto() WSAEPFNOSUPPORT (10046) Protocol family not supported.
Berkeley description: A file descriptor argument was out of range, referred to no open file, or a read (write) request was made to a file that was only open for writing A database query failed because it was actively refused. WSAEPFNOSUPPORT 10046 Protocol family not supported. Error Description List
Because DHCP can be, well, a little finicky in the stability department. I am currently sending approx. 200 bytes of data to this device every 30 seconds - the throughput of data is small. WinSock description: Same as Berkeley, and then some. No more results can be returned by the WSALookupServiceNext function.
An established connection was aborted by the software in your host machine, possibly due to a data transmission timeout or protocol error. User suggestions: Check your WinSock, protocol stack, network driver and network interface card configuration. this is the code I loop in the client: Code: while( ! WSA_IO_PENDING 997 Overlapped operations will complete later.
For example, the value given for the origin when positioning a file pointer (by means of a call to fseek) is before the beginning of the file. WSA_QOS_EFILTERSTYLE 11019 Invalid QoS filter style. Additional functions: With a datagram socket: send() or sendto(), or FD_READ. Decreasing the value is not supported.
It would also timeout if a (FIN)ish TCP packet is not ACK'd (and even if the FIN is ACK'd, it will eventually timeout if a FIN is not returned). WinSock functions: gethostbyaddr(), gethostbyname(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() Additional functions: It is strange that the asynchronous protocol and services functions can fail with this error, but the synchronous cannot. WSAEINPROGRESS 10036 Operation now in progress. A connection attempt failed because the connected party did not properly respond after a period of time, or the established connection failed because the connected host has failed to respond.
WSAEFAULT 10014 Bad address. An invalid shaping rate object was found in the QoS provider-specific buffer. The Windows default TCP/IP settings are designed to work with either very low-speed connections (dial-up) or very low-latency connections (ethernet LANs, for instance).
© Copyright 2017 nbxcorp.com. All rights reserved.