Repair Winsock Error Wsaeconnaborted 10053 (Solved)


Home > Winsock Error > Winsock Error Wsaeconnaborted 10053

Winsock Error Wsaeconnaborted 10053

Contents

An invalid shaping rate object was found in the QoS provider-specific buffer. However, the WSAEPROTONOSUPPORT is another possible equivalent for WinSock to use in place of this error. Developer suggestions: Every application that uses non-blocking sockets must be prepared for this error on any call to the functions mentioned below. The server application might need to call htons() to translate the port to network byte order in the sockaddr structure. have a peek at this web-site

WinSock functions: socket() See also: WSAEPROTOTYPE, WSAEPROTONOSUPPORT WSAESTALE (10070) Stale NFS file handle. This error is returned from operations on nonblocking sockets that cannot be completed immediately, for example recv when no data is queued to be read from the socket. This is what occurs in Berkeley Sockets. Waitable Timers – Call CreateWaitableTimers() to make a waitable timer, which you can then pass to a function like WSAEventSelect() along with your sockets: if none of the sockets is signalled

Winsock Error 10053

You will receive 10 karma points upon successful completion! NOTE: You can increase the value only for the initial time-out. Handle the request as a non-fatal error (if possible), since some WinSock's can legally fail the request. It would also timeout if a (FIN)ish TCP packet is not ACK'd (and even if the FIN is ACK'd, it will eventually timeout if a FIN is not returned).

  1. WinSock description: Same as Berkeley, and then some.
  2. Another possible reason for the WSAEACCES error is that when the bind function is called (on Windows NT 4.0 with SP4 and later), another application, service, or kernel mode driver is bound to
  3. All rights reserved.
  4. This usually means the local software knows no route to reach the remote host.
  5. Assuming you have a name server configured instead of or as well as a host table, a hostname resolution request causes a WinSock DLL to send a DNS "A" record query
  6. all other functions: retry the operation again later since it cannot be satisfied at this time.
  7. Developer suggestion: are you trying to use an optional feature?

Berkeley description: An asynchronous signal (such as SIGINTor SIGQUIT) was caught by the process during the execution of an interruptible function. TCP, UDP, ICMP, ARP, DNS) that typically causes the error. An invalid QoS provider-specific buffer. Socket Error 10049 For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM.

No such service is known. A retry at some time later may be successful.WSAVERNOTSUPPORTED (10092)WINSOCK.DLL version out of range.The current Windows Sockets implementation does not support the Windows Sockets specification version requested by the program. These errors might be reported on any function that does network I/O (e.g. http://www.altn.com/Support/FAQ/FAQResults/?Number=KBA-01510 Is this number of retransmission retries configurable?

Not the answer you're looking for? Socket Error 10054 Connection Reset By Peer Probability of throwing a die Why cast an A-lister for Groot? TCP/IP scenario: A connection will timeout if the local system doesn't receive an (ACK)nowledgement for data sent. A connect request was made on an already-connected socket.

Winsock Error 10054

Ping a local host to verify that your local network is still functioning (if on a serial connection, see next step) Ping your local router address. WinSock description: The current WinSock implementation does not support the Windows Sockets specification version requested by the application. Winsock Error 10053 WSA_QOS_RESERVED_PETYPE 11031 Reserved policy QoS element type. What Is A Socket Error There are only a few possible causes for this error: you tried to connect to the wrong port.

A required address was omitted from an operation on a socket. Check This Out However, some WinSocks fail with WSAEINVAL you call connect() a second time (or subsequent) on a non-blocking socket. Developer suggestions: to make your application more portable: with datagram sockets don't use connect() and sendto() on the same datagram socket in an application, and always "disconnect" before calling connect() more This reset could be generated locally by the network system when it detects a connection failure, or it might be received from the remote host (in TCP terms, the remote host 10053 Winsock

The software could also be written to use number of retries before failing or time before failing or a combination of both. you didn't call setsockopt(SO_BROADCAST)). Normally results from an attempt to bind to an address that is not valid for the local machine, or connect/sendto an address or port that is not valid for a remote http://nbxcorp.com/winsock-error/winsock-error-10053-ftp.html For information, see the Handling Winsock Errors topic.

NFS is "network-related" in the strictest sense, but the Network File System protocol is an application protocol (i.e. Asynchronous Socket Error 10053 An incorrect number of flow descriptors was specified in the QoS structure. WinSock functions: With a datastream socket: connect() and FD_CONNECT WSAAsyncelect() notification message.

Returned when a provider does not return SUCCESS and does not provide an extended error code.

The way it works in Windows is as follows : An estimated RTO is first established The TCP message is sent and we wait for an ACK (acknowledge) packet If the The specified file handle is not a valid file-handle value or does not refer to an open file; or an attempt was made to write to a file or device opened Berkeley description: The attempted operation is not supported for the type of object referenced. Winsock Error 10061 Berkeley description: The host you were connected to crashed and rebooted.

It means that there is a blocking operation outstanding. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. WSA_QOS_NO_SENDERS 11007 No QoS senders. have a peek here In WinSock it means a blocking operation was interrupted by a call to WSACancelBlockingCall.

This quick tutorial will help you get started with key features to help you find the answers you need. WSATRY_AGAIN 11002 Nonauthoritative host not found. An existing connection was forcibly closed by the remote host. It also occurs with functions that take a socket handle and a sockaddr structure as input parameters.

Glad it was resolved. –gled Jul 13 '13 at 14:59 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up WSANO_RECOVERY 11003 This is a nonrecoverable error. Historical Number PRI5720 Product Alias/Synonym Fact winsock error messages Connect:Direct Windows All Releases 7.0.11932010.2834905 Goal FAQ: What are the meanings of the Winsock Error Codes? WSA_QOS_EFILTERTYPE 11020 Invalid QoS filter type.

WinSock functions: accept(), bind(), closesocket(), connect(), gethostbyaddr(), gethostbyname(), gethostname(), getpeername(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), getsockname(), getsockopt(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), sendto(), setsockopt(), shutdown(), socket(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), In some instances, it also refers to the current state of the socket—for instance, calling accept on a socket that is not listening. Is there any way to bring an egg to its natural state (not boiled) after you cook it?